This is a required field.
Invalid
Part number
Error in validation!

Nano Scratch Tester:
NST³

  • media
  • +5
  • 360°
  • Measurement of coating adhesion and scratch resistance
  • Full panorama image synchronized with all other signals such as penetration depth and friction force
  • Ideal for thin coatings below 1000 nm thickness
  • Force measurement up to 1000 mN 

The NST³ nano scratch tester is particularly suited for characterizing the practical scratch resistance and adhesion failure of thin films and coatings with a typical thickness below 1000 nm. NST³ can be used to analyze organic and inorganic coatings as well as soft and hard coatings. The unique design of the nano-scratch measurement head includes two sensors for force and depth measurements associated with a state-of-the-art piezoelectric actuator. These unique features provide a fast response time (down to milliseconds), great accuracy, and great flexibility for all kinds of scratch measurements.

Combine instrumented indentation testing heads with scratch testing heads, a nanotribometer, and even an atomic force microscope on a unique Step surface testing platform.

Key features

Access to full synchronized panorama for analysis whenever, wherever

Access to full synchronized panorama for analysis whenever, wherever

This unique feature automatically synchronizes the panoramic image of the whole scratch in perfect focus with scratch data from all sensors. You can therefore perform critical loads analysis based on panorama observation and signal recordings at any time. Anton Paar is the exclusive holder of the synchronized panorama technique (U.S. patent 8261600 and the European patent EP 2065695).

Fast response time to small forces applied

Fast response time to small forces applied

The NST³ nano scratch tester incorporates a double cantilever beam for application of the load combined with a piezoelectric actuator for an ultra-fast response to the load applied. This concept also corrects the result for deviations caused by any event occurring during the scratch (e.g. appearance of cracks and failure, defects, or non-flat sample). 

No compromises: Apply exactly the force you want

No compromises: Apply exactly the force you want

The closed active force feedback loop provides even more accurate nano scratch testing. NST³ incorporates a real sensor for force measurement that directly feeds back to the normal force actuator. This ensures reproducible scratch testing, even when you investigate more complex surface geometries like non-parallel, rough, or curved samples.

True penetration depth measurements for elastic recovery studies

True penetration depth measurements for elastic recovery studies

The NST³ nano scratch tester incorporates a real displacement sensor for monitoring the vertical motion of the indenter. Thanks to this sensor, the unique technique of pre- and post-scan allows you to get the true depth: elastic, plastic, and viscoelastic properties of materials can therefore be evaluated. This technique involves a pre-scan recording the surface profile (form, waviness, and roughness) of the sample before performing the scratch test. NST³ corrects the indenter depth during the scratch (penetration depth) and after the scratch (residual depth) using the surface profile.

Multi-post-scan mode to measure the viscous behavior after a scratch

Multi-post-scan mode to measure the viscous behavior after a scratch

After a scratch, you can define unlimited post-scan measurements in the software with a delta in time to measure the residual depth. This new analysis will give you additional understanding of the deformation behavior of your surface versus the recovery time.

Technical specifications

Maximum load [mN] 1000
Load resolution [μN] 0.01
Load noise floor [rms] [μN] 0.1
Loading rate [N/min] Up to 100
Maximum friction force [mN] 1000
Friction force resolution [μN] 1
Maximum depth [μm] 600
Depth resolution [nm] 0.1
Depth noise floor [rms] [nm] 1.5
Data acquisition rate [kHz] 192
Scratch speed [mm/min] 0.1 to 600

Standards

Open all
Close all

ASTM

D7187

Anton Paar Certified Service

The Anton Paar quality in service and support:
  • More than 350 manufacturer-certified technical experts worldwide
  • Qualified support in your local language
  • Protection for your investment throughout its lifecycle
  • 3-year warranty
Learn more

Documents

Categories
Industry
Application
Product
Your choice: Reset all filters

No results found!

See more

Similar products

Accessories

Accessories

Accessories

Accessories

Not all items are purchasable online in specific countries.

To find out if you can purchase online from your location, check the online availability below.

Mechanical Surface Testing Platforms:
Step 

More info
Online price only | excl.incl. 0VAT
Delivery time: %1$s – %2$s working days %1$s – %2$s weeks %1$s – %2$s months