• Semiconductor metrology

    How to improve the wafer production process and ensure high-quality wafers

  • To support you in producing the highest-quality wafers, Anton Paar provides wafer metrology tools for monitoring the quality of your thin films, evaluating the surface roughness during metallization, understanding the surface chemistry of outer layers, and characterizing wafer defects. Our instruments will help you determine and adjust many different parameters throughout the wafer manufacturing process to create a better end product.

    Wafer metrology in the production process

    From thin films to testing, assembly, and packaging, our measurement solutions support you at every manufacturing step.

    Thin films

    It is important to have full control over the parameters influencing the thin film deposition process and measuring instruments which monitor these parameters can support you here. As thin films usually have a thickness between a few nanometers and about 100 micrometers, and in some cases even a few atoms, this requires wafer metrology instruments which operate in the nano- and sub-nanometer range. The surface quality of such thin layers is best determined by investigating the roughness with an Atomic Force Microscope (AFM). To analyze the proper adhesion, scratch resistance, and hardness of the layers and therefore ensure the quality of the end product and further production steps, you need to apply scratch testing and instrumented indentation testing. These methods give insight into the mechanical properties of the deposited layers.

    Measuring the zeta potential of the outer layer with Anton Paar’s surface charge analyzer provides you with information on its surface chemistry and thus its composition.

    Browse solutions


    To help avoid contamination of the photomasks after the cleaning process you can perform a zeta potential analysis and use the results to optimize the cleaning process. For defect analysis on the photomask an AFM is sensitive enough to reveal the smallest imperfections and aid in controlling the repair process.

    Browse solutions


    To achieve reproducible etching results you need to be in full control of the concentration of the hydrofluoric acid used. Anton Paar’s density meter with a chemically resistant measuring cell delivers concentration values in minutes so you can obtain consistent etching.

    Different etching strategies also have an effect on the surface chemistry of the wafer. Make use of zeta potential analysis with Anton Paar’s surface charge analyzer to follow the effect of etching on the outermost wafer surface.

    Use Anton Paar’s atomic force microscope to check and quality control certain parts of a wafer after etching. AFMs give quick results and can easily find and test the same spot over and over again, also automatically measuring predefined patterns. This makes them the perfect tool to characterize defects, determine spacer dimensions, and analyze critical dimension (CD), line width roughness, and line edge roughness.

    Browse solutions


    Cleaning is a critical step in the manufacturing process of wafers, requiring the removal of chemical and particle impurities without altering or damaging the wafer surface or substrate. Anton Paar’s measuring devices help you keep the following under control:

    Sulfuric acid concentration

    One of the most important parameters is the concentration of the sulfuric acid which you can measure with a chemically resistant density and sound velocity meter. Exact knowledge of the concentration of the sulfuric acid guarantees a consistent cleaning process.

    Purity of ultrapure water

    Properly functioning membranes are a prerequisite to having ultrapure water for the cleaning process. Using a surface charge analyzer to determine the zeta potential of the membrane-water interface gives you a clear understanding of the membrane’s behavior. Unexpected membrane fouling can thus be prevented and you can step in before there is degradation of the water purity.

    Wafer uniformity after CMP

    To guarantee wafer uniformity after CMP (chemical-mechanical polishing) use an atomic force microscope to determine the effective field height (EFH). AFM is a non-destructive method for wafer surface inspection which measures very small features with superior accuracy.

    Browse solutions


    To support you during planarization, Anton Paar provides two devices for reducing contamination in these process steps: one for solids, one for particles. Evaluating polishing pads and slurry particles by determining the zeta potential gives you the knowledge you need to decide when to replace pads based on their performance. Zeta potential measurements on wafer surfaces and slurry particles used in the CMP process alert you to the potential for particle adhesion due to electrostatic interactions. With this knowledge you can optimize the conditions to prevent this from happening.

    Browse solutions

    Testing, assembly, and packaging

    The right packaging is essential to save the precious wafers from damage. Therefore it is important to ensure that the used materials (bond pads, connections, and ball grid arrays) have the correct mechanical properties. You can face this challenge by performing measurements on predefined spots on the microchip to determine the hardness and elastic modulus with a nanoindentation tester and/or ultra nanoindentation tester.

    Browse solutions

    Further related applications

    Surface characterization is also an important task for products related to wafer production such as displays and optoelectronics. When manufacturing displays you can measure the adhesion with a micro scratch or nano scratch tester and evaluate the mechanical properties with a nanoindentation tester or a combination of both methods. The results will give you insights into and full control of the layer quality. The arrays and shape of microlenses are best measured with Anton Paar’s atomic force microscope as it provides you with the lateral dimensions as well as the height of each individual microlens.

    Browse solutions

  • Find your solution

    Solution Your benefit Instrument
    Thin films
    You want to monitor the quality of thin-film coatings. Perform surface charge analysis (zeta potential measurements) at the outermost surface layer. Information on the surface chemistry that confirms the desired composition of the outermost thin film layer  
    You need precise and time-efficient roughness control during metallization to ensure the quality of the subsequent processing steps. Measure surface roughness over a wide dynamic range with atomic force microscopy (AFM) and obtain quantitative results combined with 3-dimensional information. Reproducible adhesion of deposited materials, reproducible interfaces in the transistor gate stack, quality control of electrical contacts (such as source, drain, and gate contacts) and also wafer backsides for power electronics (such as IGBTs)  
    As an integrated circuit (IC) designer and manufacturer, you want to ensure that the materials and layers used in IC production have the correct mechanical properties. Characterize the hardness and elastic modulus and adhesion of thin layers on wafers with mechanical surface characterization (using nano scratch testing and low-load indentation testing). Full control of the deposited functional layers during the integrated circuit development  
    You need to control the quality of the metallization process, as a change of parameters has impact on the grain size distribution. Determine grain size and distribution with atomic force microscopy. Ensuring that a change of process parameters does not cause issues in bonding  
    You want to avoid contamination of photomasks, which affects the quality of integrated circuits. Determine the correlation between different cleaning agents and the photomask by measuring the zeta potential ( surface charge analysis). Optimization of the performance of cleaning procedures for photomasks  
    A high-precision defect analysis is essential for you to control the quality of your photomasks, as any imperfection will be transferred to the sample pattern. For defect analysis, determine the initial defect volume with atomic force microscopy to reveal imperfections. Optical proximity correction (free of proximity effects) to control the repair progress with a precise localized measurement.  
    You want to determine the concentration of the hydrofluoric acid to get a consistent etching performance. Perform a concentration measurement with a chemically resistant Hastelloy U-tube density meter to determine the hydrofluoric acid concentration. Reproducible etching processes by quickly checking the acid concentration beforehand  
    You need to characterize defects that appear after dry etching and detect whether it is a particle or a pit in order to define countermeasures for the process step. Perform atomic force microscopy for precise analysis of size, shape, and 3-D topography of the defects. Definition of correct process parameters due to the reproducible, quantitative, and rapid defect analysis  
    You want to check the spacer dimensions several times and evaluate the effects of etching as the dimensions are directly related to the electrical performance of the final transistor. Characterize the sidewall thickness and profile throughout the steps of the gate processing with atomic force microscopy. Full control of gate processing by measuring the exact same gate several times (re-finding the exact same position is only possible with AFM).  
    You are searching for a fast technique to analyze critical dimension (CD), line width roughness, and line edge roughness after the lithographic and etching process steps. Get vertical line/trench profile information in nanometer resolution and superior accuracy with atomic force microscopy. The Tosca AFM series is designed for fast AFM measurements, provides a short time-to-result, and guarantees the highest quality of subsequent process steps.  
    You need to control the fin dimensions of the fin field effect transistor (FinFET) formation process, which is critical to product performance. Analyze the FinFET structure with high-precision atomic force microscopy, as changes in fin dimensions come from line height, width, and profile variations. Full control of the FinFET dimensions with precise AFM measurements in the sub-nm range  
    You want to quickly determine the concentration of sulfuric acid, approx. ten times faster than with the traditional titration method. Measure density and sound velocity with one instrument ( concentration measurement). Due to the non-linear concentration curve of sulfuric acid both technologies are required. High repeatability and reproducibility of the cleaning process  
    You need to ensure the membrane quality to get ultrapure water for semiconductor processes. Determine the membrane’s surface zeta potential ( surface charge analysis) to monitor the membrane quality and prevent unexpected membrane fouling and the degrading of water purity. Reliable water purity for semiconductor device manufacturing  
    You need to guarantee wafer uniformity after CMP (chemical-mechanical polishing) by knowing the effective field height (EFH), which affects the threshold characteristics of transistors. Monitor the EFH specification with atomic force microscopy, as high variations can lead to failures. Superior accuracy of EFH control with a quick and non-destructive method to measure such small features  
    You want to avoid contamination of silicon wafers with different top coatings due to contact with components of the slurry during the process of CMP. Determine the zeta potential of wafer surfaces and slurry particles with surface charge analysis to optimize process conditions and avoid particle adhesion through electrostatic interactions. Reduced cycle times in post-CMP cleaning thus increasing throughput  
    It is important for you to avoid cross-contamination in CMP processes through polishing pads. Characterize polishing pads and slurry particles with surface charge analysis to predict electrostatic attraction. Reduction of the replacement frequency of polishing pads to save time and money  
    Test, assembly, and packaging
    As a semiconductor packaging service provider you have to make sure that the packaging process is done correctly and the used materials (bond pads, connections, ball grid arrays, etc.) have the correct mechanical properties. Perform local measurements with a nanoindentation tester to determine the hardness and elastic modulus ( mechanical surface characterization). Verification of the IC packaging process in order to ensure the highest packaging material quality  
    Further related applications: Displays
    As a display manufacturer you want to know about the mechanical properties and adhesion of the display layers to avoid premature delamination or aging and also to monitor the quality of the layers. For this mechanical surface characterization, measure the adhesion (with micro scratch or nano scratch testers) and the mechanical properties of the layers (with a nanoindenation tester). Full control of the layer quality in display manufacturing  
    Further related applications: Optoelectronics
    You need to control the quality of the microlens array and shape. This knowledge is critical for improving its quality and yield. With atomic force microscopy measure each individual microlens to get lateral dimensions as well as height. Precise topography measurements over multiple microlenses  

    You did not find your specific situation? Anton Paar still has the solution for your challenge. Just contact us for more information. 

  • Automation in your quality control lab

    Anton Paar also offers fully customized automation solutions to fulfill your individual requirements.

    Modular sample processor

    A customized Modular Sample Processor can be tailored around your laboratory workflow, e.g. when measuring acids and bases. The system automates your sample identification, vial capping, sub-sampling, and mixing.

    High-throughput platform HTX

    Anton Paar’s HTX is the cutting edge platform for the implementation of sample preparation and analytics into one customized automated solution. As well as Anton Paar’s own devices, instruments from third-party suppliers can also be implemented.


    • Analyze and prepare many samples for downstream analytics in the fastest possible way
    • Keep your team safe when dealing with hazardous substances
    • Avoid human errors
    • Run your system 24/7
    • Use bi-directional communication with your LIMS which guarantees maximized flexibility in terms of different workflows for sample preparation 
  • 3-year warranty

    • Effective January 1, 2020, all new Anton Paar instruments* include repair for 3 years.
    • Customers avoid unforeseen costs and can always rely on their instrument.
    • Alongside the warranty there is a wide range of additional services and maintenance options available.

    * Due to the technology they use, some instruments require maintenance according to a maintenance schedule. Complying with the maintenance schedule is a prerequisite for the 3-year warranty.

    Learn more

  • Webinar

    Semiconductor metrology: How to determine, control, and improve various parameters during the wafer production process


    In this webinar we will present a mix of different solutions to help you ensure and control the quality during almost every step in the whole wafer production process.

    Find out more about the following techniques:

    • Reproducible, quantitative, and rapid surface roughness and height measurements with high precision using AFM: This technology is known for its unprecedented precision and reproducibility, but has often been considered too time-consuming and thus not efficient enough. In this webinar, we focus on the new-generation usability and efficiency of Tosca AFM measurements and show the benefits for efficient, fast, and reliable AFM wafer analysis.
    • Surface charge analysis used as a direct tool to monitor wafer cleaning effects: We discuss how knowledge of the zeta potential is used to tune wafer-particle interactions in the CMP process.
    • Mechanical surface characterization of layers on wafers on the nanoscale with nanoindentation and nano scratch measurements: These two techniques can be used to measure hardness, adhesion, or scratch resistance of thin films on wafers in microchip production or on protective layers on glass in display manufacturing.
    • Accurate, fast, efficient, and safe concentration measurement of chemicals for semiconductor production: Learn how easy it is to use a digital density meter to determine the concentration of several acids and bases. High measurement performance is key for quality inspection during etching and cleaning steps in the semiconductor industry.