Sample Changer:
Xsample 330
- The single sample changer for a wide range of samples
- Prevents sample carry-over with automatic rinsing and drying after each sample
- Highly resistant wetted parts for handling aggressive samples
The new industrial grade peristaltic pump in combination with automatic cleaning makes Xsample 330 perfectly suitable for measuring single low-viscosity samples with widely different properties in direct succession. Once measured, the sample is drained or recovered and the system is automatically cleaned with up to two cleaning agents. A drying step is performed by the operator to perfectly prepare the measurement cell(s) for the next sample.
Key features
Automatic cleaning
- Automatic rinsing and drying after each sample for perfect preparation of the system
- Up to two different cleaning agents can be used in any order for an individual cleaning procedure.
- Advanced settings for cleaning procedures to increase measuring performance
For a wide range of samples
- Filling with peristaltic pump covers a wide range of different sample viscosities up to 3,000 m.Pas
- All wetted parts of Xsample 330 (high resistance) are made of durable materials for aggressive samples, such as phosphoric acid or trichloroacetic acid
- Adjustable filling modes for different types of samples enable perfect measuring results
Highly efficient sample handling and easy operation
- Depending on the system size, only a minimum amount of sample volume is needed to perform a measurement
- Easy operation by an integrated user interface on the master instrument
- Straightforward measurements of different sample viscosities due to a sensor-controlled stop of the filling procedure
- Automatic sample recovery returns expensive or hazardous samples back to their vials
Technical specifications
Viscosity range | up to 3,000 mPa•s at ambient and measuring temperature¹ |
Filling mode | with peristaltic pump:
|
Typical time for filling and measuring cycle | 2 to 5 minutes |
Minimum sample volume | approx. 10 mL to 20 mL |
Compressed air supply | max. 2 bar (29 psi) relative |
Quality of air necessary | Class 3 according to ISO 8573-1: max. particle size: 5 μm max. pressure dew point: –20 °C (–4 °F) max. oil content: 1 mg/m³ |
Environmental conditions (EN 61010) | indoor use only |
Operating temperature | +15 °C to +35 °C (+59 °F to +95 °F) |
Pollution degree | 2 |
Over voltage category | II |
Altitude | max. 3,000 m (9,840 ft) |
Power supply | supplied by the master instrument AC power supply voltage according to technical data plate at the rear of the master instrument (protective grounding required) |
Dimensions excl. master instrument (L x W x H) | 205 mm x 148 mm x 205 mm (8.1 in x 5.8 in x 8.1 in) |
Weight excl. master instrument | approx. 3.8 kg (8.4 lbs) |
¹ Recommended for samples with a viscosity up to 500 mPa•s at ambient and measuring temperature. For samples with a viscosity higher than 500 mPa•s at ambient and measuring temperature, bubbles may occur during filling.
Anton Paar Certified Service
- More than 350 manufacturer-certified technical experts worldwide
- Qualified support in your local language
- Protection for your investment throughout its lifecycle
- 3-year warranty
Documents
-
Brochure | Vaccine analysis Brochures
-
Xsample Series Brochure Brochures
Compatible instruments
Consumables
Consumables
If you do not find the item you require, please contact your Anton Paar sales representative.
To find out if you can purchase online from your location, check the online availability below.
BOTTLE FOR RINSING LIQUID
HOSE 220x3x2 FEP 2x1/4"-28 UNF "CC"
"HOSE 163x3x2 PTFE 2x1/4""-28 UNF"
HOSE 710x3x2 PTFE 2x1/4"-28 UNF
HOSE 3.2x6.4 mm TYGON A-60-G, BLACK (FORMERLY:
NORPRENE A-60-G)
INLET FILTER FOR SOLVENT 20µm
FERRULE WITH SCREW JOINT
HOSE 750x3x2 PTFE 1x1/4"-28 UNF
CHECK VALVE SILICONE HOSE 3X5
HOSE 190x3x2 PTFE 1x1/4"-28 UNF
TUBE CLIP SET FOR 2mm (9QQ)
TUBE CLIP SET FOR 3 AND 3.5mm (9QQ)
HOSE 3.2x6.4 mm TYGON CHEMICAL (FORMERLY:
NORPRENE CHEMICAL)
HOSE 2.5 x 4.5 NOVOPRENE